Short answer: Touch the tester to the hot wire with its earth probe or lead in the soil, the way your tester's instructions show, and read the voltage at the far end of the fence. Manitoba Agriculture's electric-fencing guide says to "Aim for ≥2,000 V summer / ≥4,000 V winter at the far end of the fence."
What should an electric fence tester read?
Manitoba Agriculture lists these target voltages for an energizer:
- "Summer: ≥ 2,000 volts (dry ground, thinner hair coats)."
- "Winter: ≥ 4,000 volts (thicker hair, snow/ice reduce grounding)."
The same guide's installation checklist puts the reading at the end of the line: "Test voltage: Aim for ≥2,000 V summer / ≥4,000 V winter at the far end of the fence." A reading taken right at the energizer only tells you what is leaving the energizer, not what an animal meets at the far end. For why a fence reads lower once the ground freezes, see our guide Electric Fence Not Working in Winter? Grounding, Voltage and Hot/Ground Wires.
How to use an electric fence tester
- Read the instructions that come with your tester first. Testers differ in range, in how the earth probe or lead is used and in whether they need a battery.
- Push the earth probe or lead into the soil and touch the tester's contact to the hot wire, as the instructions show.
- Take the reading at the far end of the fence, where Manitoba Agriculture sets its target.
- Write the reading down. Manitoba Agriculture's checklist says: "Record baseline: Note typical voltage readings for future troubleshooting."
- If the reading is lower than usual, walk the fence. The checklist says: "Walk the line: Confirm clear of vegetation and debris." Its maintenance list adds: "Vegetation control: Keep grass/brush off wires to prevent voltage drop."
How to test the ground rods with a voltmeter
Manitoba Agriculture calls grounding the most critical component of an electric fence and gives this test:
- "“Ground out” the fence (e.g., press a metal bar against a hot wire) and measure the ground system with a voltmeter."
- "If the ground rod reading is > 200 V, add more ground rods."
- "A well-grounded system should read near 0 V at the ground rods."
Its grounding configuration is a "Minimum of 3 ground rods, each 6–8 ft (1.8–2.4 m) long." Follow your energizer's and your tester's instructions when you short the fence for this test. Ground rods, clamps and the rest of the parts list are in our guide Electric Fence Supplies Checklist: Ground Rods, Insulators, Gates and Testers.
Fence tester, digital voltmeter or fault finder?
Manitoba Agriculture's maintenance advice is to "Carry a voltmeter or fault finder—regular checks keep performance high and speed up repairs by pointing to fault direction."
- A light or audible tester shows whether the line is live and roughly how strong it is, without an exact number.
- A digital voltmeter shows the reading as a number, which is what you need to compare against the summer and winter targets above and against your own baseline.
- A fault finder also shows current and which direction it is flowing, so you can follow the line toward a short.
- A load tester puts a fixed load on the energizer so you can see what it delivers under load.
If an energizer is not putting out enough for the length of fence, see Electric Fence Energizer Sizing: How Many Joules Do You Need?
Fence testers we list
- Light and audible testers: Patriot six light fence tester · Corral fence checker, visual and audible
- Digital voltmeters: Patriot digital voltmeter · Speedrite digital voltmeter · Corral fence tester up to 10,000 V
- Fault finders: Speedrite digital fault finder · Speedrite remote control / fault finder
- Load and battery testers: Tru-Test 500 ohm load tester · Corral battery tester 6–20 V
- Everything in one place: Fence testers and voltmeters
Sources: Manitoba Agriculture, "Everything You Need to Know About Electric Fencing", re-checked November 11, 2026.